Customer Reviews

What are your beliefs about How to Install a Bathtub?

Mounting a bathtub isn't precisely brain surgery, but it does need solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a new one is additionally a moderately tough project. If the old bathtub is readily obtainable, the project can relocate rapidly; if you need to open a wall surface to get rid of the old tub and also position the brand-new bathtub, the job is a lot harder. In either situation, the project is within a house handyman's skills, although you will need a helper to vacate the old bathtub and also set in the new one. Make sure you have qualified yourself for the task and also are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed project, it is far better to think about employing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This write-up will help you set up a brand-new bath tub in your restroom if you have actually currently bought a new tub as well as do not require to change the arrangement of your previous supply of water pipelines.
Your devices and material checklist must consist of the following:

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Preparing for the Installment

To start with, the sustaining frame supplied with the bath must be fitted (if needed) according to the supplier's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make sure that if the faucet features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to avoid stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its last placement.

Removing Old Touches

If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be rather troublesome due to the limited accessibility that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a towel prepared for the staying water that will come from the pipelines. When the supply pipes have actually been eliminated, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before proceeding to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.

Installing the Bath tub

Utilizing the two wood boards under its feet, put the bathtub in the needed position. The wood boards are practical in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the tub till the spirit level reviews level.
To mount taps, fit all-time low of the outermost flexible faucet connector to the proper supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the water supply and inspect all joints and new pipework for leakages and tighten them if needed. Fill the tub as well as likewise inspect the overflow outlet as well as the regular outlet for leakages.
Finally, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub should wait up until the bath tub has actually been utilized at the very least once as this will certainly resolve it into its final placement.

Fitting New Taps

If the tails of the new faucets are plastic, then you will need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Safeguard the tap in place with the manufacturer provided backnut. Once the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The former type ought to be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.

Tiling Around the Bathtub

In the area where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to fracture an inflexible seal, creating the water to penetrate the wall between the bathroom and also the tiling, leading to difficulties with moisture as well as feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes and also cartridges, and are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to permit the activity experienced when the bathtub remains in usage. The sealer can split relatively early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof adhesive and also cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I'm very excited about How to Install a Bathtub and I am assuming you enjoyed my article. Those who enjoyed reading our blog entry if you please remember to pass it around. Thanks for your time. Please pay a visit to our blog back soon.

Click Here